STM32G474 ADC無法正常啟動轉換怎么辦

提問

void MX_ADC3_Init(void)
{

ADC_MultiModeTypeDef multimode = {0};
ADC_ChannelConfTypeDef sConfig = {0};

hadc3.Instance = ADC3;
hadc3.Init.ClockPrescaler = ADC_CLOCK_SYNC_PCLK_DIV4;
hadc3.Init.Resolution = ADC_RESOLUTION_12B;
hadc3.Init.DataAlign = ADC_DATAALIGN_RIGHT;
hadc3.Init.GainCompensation = 0;
hadc3.Init.ScanConvMode = ADC_SCAN_DISABLE;
hadc3.Init.EOCSelection = ADC_EOC_SINGLE_CONV;
hadc3.Init.LowPowerAutoWait = DISABLE;
hadc3.Init.ContinuousConvMode = ENABLE;
hadc3.Init.NbrOfConversion = 1;
hadc3.Init.DiscontinuousConvMode = DISABLE;
hadc3.Init.ExternalTrigConv = ADC_SOFTWARE_START;
hadc3.Init.ExternalTrigConvEdge = ADC_EXTERNALTRIGCONVEDGE_NONE;
hadc3.Init.DMAContinuousRequests = DISABLE;
hadc3.Init.Overrun = ADC_OVR_DATA_PRESERVED;
hadc3.Init.OversamplingMode = DISABLE;
if (HAL_ADC_Init(&hadc3) != HAL_OK)
{
Error_Handler();
}

/** Configure the ADC multi-mode
*/
multimode.Mode = ADC_MODE_INDEPENDENT;
if (HAL_ADCEx_MultiModeConfigChannel(&hadc3, &multimode) != HAL_OK)
{
Error_Handler();
}

/** Configure Regular Channel
*/
sConfig.Channel = ADC_CHANNEL_1;
sConfig.Rank = ADC_REGULAR_RANK_1;
sConfig.SamplingTime = ADC_SAMPLETIME_92CYCLES_5;
sConfig.SingleDiff = ADC_SINGLE_ENDED;
sConfig.OffsetNumber = ADC_OFFSET_NONE;
sConfig.Offset = 0;
if (HAL_ADC_ConfigChannel(&hadc3, &sConfig) != HAL_OK)
{
Error_Handler();
}
/* USER CODE BEGIN ADC3_Init 2 */

/* USER CODE END ADC3_Init 2 */

}

HAL_ADCEx_Calibration_Start(&hadc3, ADC_SINGLE_ENDED);

HAL_ADC_Start(&hadc3);

仿真時，查看DR寄存器，只有在開始運行仿真時轉換一次就不再轉換，改成外部TIM觸發也只是能轉換一次，是哪里配置錯誤嗎？

最新回答

• 

  xmshao 昨天10:18

  我看你的配置，單個通道，連續轉換。估計是誤會了，肯定是啟動了，不然一個結果也沒有。

  可能調試模塊沒有做更新，你也沒有啥操作。

  保持現有 配置的前提下，你這樣試試，先軟件啟動ADC，然后查詢接收，再看看結果。

  int main(void)
  {

  。。。。。。
  。。。。。。

  uint8_t i=0;

  HAL_ADC_Start(&hadc1);

  while (1)
  {

  if (HAL_ADC_PollForConversion(&hadc1, 888) != HAL_OK)
  {

  Error_Handler();
  }

  AdcResulti++] = HAL_ADC_GetValue(&hadc1);

  if(i==9) i=0;

  } //while(1)

  } //main