如何在NXP源碼基礎上適配ELF 1開發板的PWM功能

elf@ubuntu:~/work$ tar jvxf linux-imx-imx_4.1.15_2.0.0_ga.tar.bz2
elf@ubuntu:~/work$ cd linux-imx-imx_4.1.15_2.0.0_ga/
elf@ubuntu:~/work/linux-imx-imx_4.1.15_2.0.0_ga$ ls

將arch/arm/configs路徑下的imx_v7_mfg_defconfig復制一份，命名為imx6ull_elf1_defconfig

elf@ubuntu:~/work/linux-imx-imx_4.1.15_2.0.0_ga$ cp arch/arm/configs/imx_v7_mfg_defconfig arch/arm/configs/imx6ull_elf1_defconfig

將arch/arm/boot/dts路徑下的imx6ull-14x14-evk.dts復制一份，命名為imx6ull-elf1-emmc.dts

elf@ubuntu:~/work/linux-imx-imx_4.1.15_2.0.0_ga$ cp arch/arm/boot/dts/imx6ull-14x14-evk.dts arch/arm/boot/dts/imx6ull-elf1-emmc.dts

elf@ubuntu:~/work/linux-imx-imx_4.1.15_2.0.0_ga$ vi arch/arm/boot/dts/Makefile

elf@ubuntu:~/work/linux-imx-imx_4.1.15_2.0.0_ga$ vim build.sh

#!/bin/bash
export CPUS=`grep -c processor /proc/cpuinfo` 
source /opt/fsl-imx-x11/4.1.15-2.0.0/environment-setup-cortexa7hf-neon-poky-linux-gnueabi
make distclean
make imx6ull_elf1_defconfig
make -j${CPUS}
rm -rf ./.tmp
make modules_install INSTALL_MOD_PATH=./.tmp/rootfs/
cd .tmp/rootfs/
tar -jcvf modules.tar.bz2 *

elf@ubuntu:~/work/linux-imx-imx_4.1.15_2.0.0_ga$ chmod 777 build.sh

從上圖可以看出PWM2連接到了連接器的65腳。接下來我們需要找到這個引腳在軟件上的信號名稱。

打開ELF 1開發板資料包5-硬件資料5-4 管腳分配表ELF 1引腳復用對照表找到65引腳的信號名稱。

pinctrl_pwm2: pwm2grp {
                        fsl,pins = <
                             MX6UL_PAD_GPIO1_IO09__PWM2_OUT   0x110b0
                        >;
                };

在設備樹文件arch/arm/boot/dts/imx6ull.dtsi中已經定義好了8路PWM信號的相關節點，只需要將PWM2的時鐘配置上即可，將clocks屬性的IMX6UL_CLK_DUMMY更改為IMX6UL_CLK_PWM2。

&pwm2 {
        pinctrl-names = "default";
        pinctrl-0 = <&pinctrl_pwm2>;
        status = "okay";
};

由于pwm只涉及到設備樹修改，不再使用腳本編譯，單獨編譯設備樹即可。

elf@ubuntu:~/work/linux-imx-imx_4.1.15_2.0.0_ga$ . /opt/fsl-imx-x11/4.1.15-2.0.0/environment-setup-cortexa7hf-neon-poky-linux-gnueabi
elf@ubuntu:~/work/linux-imx-imx_4.1.15_2.0.0_ga$ make dtbs

elf@ubuntu:~/work/linux-imx-imx_4.1.15_2.0.0_ga$ scp arch/arm/boot/dts/imx6ull-elf1-emmc.dtb root@172.16.0.175:/run/media/mmcblk1p1/

root@ELF1~# sync
root@ELF1~# reboot

待開發板啟動完成，將PWM2設置為輸出

root@ELF1:~#:~# echo 0 > /sys/class/pwm/pwmchip1/export

root@ELF1:~#:~# echo 1 > /sys/class/pwm/pwmchip1/pwm0/enable

root@ELF1:~#:~# echo 1000000 > /sys/class/pwm/pwmchip1/pwm0/period

root@ELF1:~#:~# echo 500000 > /sys/class/pwm/pwmchip1/pwm0/duty_cycle

root@ELF1:~#:~# echo 0 > /sys/class/pwm/pwmchip1/pwm0/enable